Tag Archives: bmw ista

BMW Diagnostic Tool, BMW ISTA

How to solve BMW F32 Programming Problem with BMW ISTA-P?

Posted on by SmartBimmer

How to solve BMW F32 Programming Problem with BMW ISTA-P? When programming BMW F32 by BMW ICOM NEXT A, always got an error reading “Vehicle programming with ISTA-P is no longer approved for the connected vehicle. Vehicle management is now only possible with ISTA4. Please observe the release notes!” Solution: For BMW F/I/G series programming, […]

Continue reading →
BMW ISTA

How to connect and set the BMW INPA K+DCAN USB interface for BMW ISTA Rheingold?

Posted on by SmartBimmer

How to connect and set the BMW INPA K+DCAN USB interface for BMW ISTA Rheingold? This is to connect the INPA cable with BMW ISTA. There is no problem with the test in this guide, but it will not be responsible for any potential loss or damage. Request for BMW Remote Support

Continue reading →
BMW Diagnostic Tool, BMW ISTA

How to Solve BMW F01 F02 High Battery Discharge Warning with BMW ICOM?

Posted on by SmartBimmer

How to Solve BMW F01 F02 High Battery Discharge Warning with BMW ICOM? For BMW F01 F02, after the vehicle is started, a Check Control message “High Battery Discharge Warning” is displayed in the Central Information Display (CID). Various power supply and power management faults are stored, including the following: CAUSE PROCEDURE Important note: All subsequent […]

Continue reading →
bmw coding

BMW VO Code List for BMW ISTA and BMW Esys

Posted on by SmartBimmer

BMW VO Code List for BMW ISTA and BMW Esys 0 Dummy-SALAPA1 Dummy-SALAPA0BV Fuel refuelling0BW Partial refuelling100 Usable load increase101 Dummy-SALAPA102 Reinforced brakes102 Chassis, officials utility vehicle103 Aggregate protective plate103 Four seasons tyres104 Middle East version105 Job control “German Federal State”106 Safety vehicle107 Preparation, tachograph108 Motor afterrun control unit109 High-security vehicle Security Plus10A Preparation armour10B […]

Continue reading →
BMW ISTA

BMW ISTA Programming P3.68 4.31 Release Notes

Posted on by SmartBimmer

BMW ISTA Programming P3.68 4.31 Release Notes 1 General notes（BMW ISTA need BMW ICOM NEXT connect to car）With the launch of ISTA 4, the functionality for programming has been integrated into ISTA. The following series can be dealt with using ISTA/P: 2 Overview of the I levels containedI level newly added or updated in this […]

Continue reading →
BMW ISTA

New Content: BMW ISTA V4.29.21 – Repair Instructions

Posted on by SmartBimmer

New Content: BMW ISTA V4.29.21 – Repair Instructions BMW ISTA needs BMW ICOM NEXT to connect BMW car Repair instructionsThe new publication has essentially been supplemented by the following Repair Instructions: The messages regarding the repair instructions, technical data, tightening torque, and operating supplies via the diagnosis system were taken into consideration and additions were […]

Continue reading →
BMW ISTA

Configure BMW ISTA 4.28.xx Software with New Firmware

Posted on by SmartBimmer

Configure BMW ISTA 4.28.xx software with new Firmware What is BMW Rheingold ISTA ? BMW ISTA is a workshop system that contains BMW AG Data and Information. ISTA stands for Integrated Service Technical Application. Way back when, during the initial development of this tool, BMW used DIS (Diagnostics Information System), and as the programs evolved […]

Continue reading →
BMW ISTA

BMW ISTA P Programming and Coding

Posted on by SmartBimmer

BMW ISTA P Programming and Coding BMW ISTA P stands for Integrated Service Technical Application Programming. It is a dealer-level diagnostic software that replaced the older version of SSS Program programming software. ISTA/P is primarily used for processing all coded, programmed, and enable-dependent control modules of BMW vehicles. With the use of a K+DCAN or […]

Continue reading →